Electric Gates in Clacton-on-Sea
Electric, sliding and driveway gate installation, repairs and servicing for homes and businesses in Clacton-on-Sea, Great Clacton, Holland-on-Sea and Jaywick. Built for sea wind and salt air.
Electric gates for Clacton and the Tendring coast
Clacton-on-Sea is a long, open stretch of coast. Wind comes straight in off the North Sea, salt settles on every exposed surface, and many homes on the seafront roads, in Holland-on-Sea and around Jaywick stand on flat plots with very little shelter. A gate here has to cope with more than a typical inland driveway.
We install, repair and service electric gates for homes and businesses across Clacton-on-Sea, Great Clacton, Holland-on-Sea, Jaywick and the villages around them. That means new swing, sliding and cantilever gates, automation for gates you already own, and repairs to gates that were fitted by someone else.
Every job starts with a free on-site survey, so the gate, the motor and the finish are chosen for your property. Our engineers travel from Chafford Hundred via the A12 and A133, and we will agree a survey time with you by phone.
Book a free site survey
What we fit and fix in Clacton-on-Sea
One contractor from survey to servicing, with one point of contact.
Electric and automatic gates
New automatic gates for houses, flats, yards and small commercial sites, with remote, keypad, intercom or phone control. Our electric gates in Essex hub shows the wider area we cover.
Sliding and cantilever gates
Where the drive is shallow or the ground is uneven, a sliding or cantilever gate opens along the boundary instead of across your drive.
Aluminium gates
Rust-proof, light on motors and finished in powder-coat colours. Aluminium gates are our usual recommendation for exposed seafront homes.
Composite gates
Wood-effect composite gates for a warmer look, without painting or staining. The frame underneath is protected against corrosion.
Driveway gates
Swing gates between piers or fence posts, designed around the width of your opening. Compare layouts on our driveway gates page.
Gate automation for existing gates
Already have manual gates? We can often add motors, safety devices and controls. For phone control on a compatible gate, see Remootio 3.
Gate repairs
Motor failures, control boards, photocells, safety edges, hinges and tracks, on any brand. See gate repairs for the faults we fix most often.
Gate servicing
Planned visits that test the safety devices, check force readings and look after the finish. See gate servicing.
Swing, sliding or cantilever?
Many homes near the Clacton seafront have a fairly shallow front garden or drive, and that often decides the gate type before style does. Swing gates need a clear arc to open. A sliding gate needs a straight length of wall or fence beside the opening but takes no space on the drive. A cantilever gate hangs from carriages and does not run in a ground track, which is useful where sand or grit blows across an entrance.
Wind matters as well. A solid-boarded gate acts like a sail in a gale, so the leaves, hinges and motors have to be sized for it. Open-bar and slatted designs let more wind through. We talk this through on the survey and fit the gate to the position, not the other way round.
Read more about sliding and cantilever gates or compare every layout on our driveway gates page.
Gates around Clacton and Holland-on-Sea
The coast changes from street to street, and so does the right gate.
Clacton-on-Sea seafront and town
Closest to the front, salt exposure is at its highest, so finish, fixings and corrosion-resistant materials matter most. In the town, we also fit gates for small yards and commercial units.
Great Clacton
Older, more established roads often have narrow or irregular openings. We measure carefully and, where space is tight, suggest slimline sliding gates or a separate pedestrian gate.
Holland-on-Sea
Quieter roads between Clacton and Frinton, with larger plots that suit wider swing or sliding gates. We also cover the rest of the coast from our Frinton-on-Sea gates page.
Jaywick and the low-lying coast
Low, open ground close to the sea calls for sealed outdoor fittings, corrosion-resistant materials and control equipment mounted off the ground. We will tell you honestly when a repair makes more sense than replacement.
Built for salt and wind
Aluminium gates do not rust, which makes them the safest long-term choice on an exposed coastal site. Composite gates weather well too, provided the steel frame inside is properly protected.
Steel gates suit some traditional properties, but any chip in the coating needs touching up before salt gets in. Whichever you choose, rinsing the gate and motor housing with fresh water now and then helps wash away salt deposits, and our servicing visits include a look at the finish.
How a gate job works in Clacton
From first call to handover, in five steps.
1. Free site survey
We visit, measure the opening, check the ground, the posts and where power will come from, and talk through the options.
2. Design and quote
You get a written quote for the gate, automation and groundworks. If you like, design a gate first in our 3D configurator.
3. Groundworks and manufacture
Foundations, posts, track or hinges and cabling are done by our team while your gate is made to size.
4. Installation and automation
We hang the gate, fit the motor, photocells, safety edges and controls, and set up your remotes, keypad or intercom.
5. Safety checks and handover
We test the safety devices, measure and record the closing forces, show you the manual release and leave you with written handover paperwork.
6. Servicing
Come back for planned servicing so the gate stays reliable and safe. See our gate servicing page.
Gate automation, repairs and design
New Gate Installation
Bespoke driveway gates in aluminium, composite or steel, with swing, sliding and cantilever options and full automation.
Explore gate systems
Repairs & Servicing
Fault diagnosis for electric gates and barriers: motors, control boards, photocells, hinges and tracks. Gates fitted by other companies welcome.
Learn about repairs
Design
Design Your Gate
Design a bespoke aluminium gate, pedestrian gate, fencing or wall in our online 3D configurator and send it to us for a quote.
Launch configurator guideGate motors we often see near you
Brand guides for opening a gate by hand. Order reflects jobs we attend across Essex — your exact motor is on the label.
Roger Technology
Manual release guide
SEA
Manual release guide
FAAC
Manual release guide
CAME
Manual release guide
BFT
Manual release guide
DEA
Manual release guide
Nice
Manual release guide
Beninca
Manual release guide
Ditec
Manual release guide
V2
Manual release guide
RIB
Manual release guide
Centurion
Manual release guide
Safety checks on every automatic gate
An electric gate is a machine that moves across a driveway, so safety is part of the job, not an extra.
Risk assessment
We look at crushing, shearing and impact points on your particular gate and plan the safety measures to suit.
Detecting obstructions
Photocells see a car, child or pet in the opening and safety edges detect contact, so the gate stops instead of closing on anyone.
Force testing
We measure the closing force with a calibrated tester and record the readings against BS EN 12453 and the current on-site method, DHF TS 013-1:2025, adjusting the motor until the gate is within the limits.
Handover and checks
You are shown the manual release and how the controls work, and the safety devices are re-checked at each servicing visit.
Clacton-on-Sea gate questions
Common questions from homeowners and businesses in Clacton, Holland-on-Sea and Jaywick.
Yes. We install, repair and service electric gates across Clacton-on-Sea, Great Clacton, Holland-on-Sea, Jaywick and the villages around them. Our engineers travel from Chafford Hundred via the A12 and A133. Call 01375 886299 or request a quote and we will arrange a free site survey.
Aluminium is our first recommendation close to the sea because it does not rust. Composite gates are a good alternative, as long as the steel frame under the boards is properly protected. Steel gates can work too, but any chip or scratch in the coating needs touching up before salt gets in. Whatever the material, an occasional rinse with fresh water helps wash salt deposits off the gate and the motor housing.
Often, yes. We look at the gate, the posts and the hinges or track on the survey and tell you honestly whether the existing gate can carry a motor or whether it is better replaced. Motors can then be controlled by remote, keypad, intercom or phone. For phone control on a compatible gate, see our Remootio 3 guide.
Yes. We repair all brands and systems, whoever fitted them: motors, control boards, photocells, safety edges, hinges and tracks. We find the root cause rather than replacing parts and hoping. See our gate repairs page for the faults we see most.
Often you do not, but it depends on the height and position. As a general rule, a gate next to a road or footpath that is taller than one metre usually needs planning permission, and homes that are listed or in a conservation area have extra rules. Tendring District Council makes the decision, so check with them before you order. We are happy to talk through your plans on the survey.
Every automated gate we fit has a manual release so you can open it by hand. We show you how it works at handover. If a gate stops working, our manual release guides cover the common motor brands, and our repairs team can attend if the fault is more than a tripped plug.
Yes. A gate that was safe on the day it was fitted needs checking to stay that way. Our servicing visits test the safety devices, check the force readings, lubricate moving parts and inspect the finish. See our gate servicing page for the plans.
Further up the coast? See our electric gates in Frinton-on-Sea page, which also covers Walton-on-the-Naze, Kirby Cross and Holland-on-Sea.
See all our electric gates in Essex, gate repairs and gate servicing and maintenance.
If you need a video, wired or GSM intercom on a new or existing electric gate in Clacton-on-Sea, see gate intercoms and GSM entry in Essex.
Ready for a gate in Clacton-on-Sea?
Get in touch for a free, no-obligation site survey and quote. We are open Monday to Friday 08:00 to 18:30 and Saturday and Sunday 09:00 to 12:00.